Hello!!

I have an airbag honda s2000 
77960-S2A-E81.
Can someone give me tested clear file because the car is away from me.
REGARDS !!

93c46 orig.rar
File Type:
Downloaded:	38 times
Size:	121 bytes

Hi, it is possible to delete error from dash? I removed dpf and have error on dash ( Particular filter clean incomplete )

I try to reset DPF service before writing flash but after error is back. In ecu I dont have errors and engine lamp is off.
did smeone have good solution for dpf off.
Here is org flash edc17,
THANKS

Attached Files

DAILY EDC17_IntFl.rar
File Type:
Downloaded:	63 times
Size:	1,012.85 KB

hello to all I can repeat myself but I did not find this thread on the orange 5 clone. so here's when long ago I bought a Chinese clone of orange 5. and a standard set of calculators and adapters. all adapters need to be revised there is missing from many a capacitor at 10 MF. watched for 5 sets of orange. So if you have a clone modify this problem. when I bought additional calculators but many of them do not work at all or work incorrectly. Dachbord and bsi works well. Inside, there is also information on connecting more than 450 help.This archive is available to all users of this site.many people ask about this software. So here it works with the Chinese clone orange




POST EDITED by MODERATOR!

Attached Files

orange 5 clone.txt
File Type:
Downloaded:	322 times
Size:	70 bytes

I would like to offer you the technique of disabling the immobelaser on the car bmw with the ms41 control unit without using the firmware of the processor. This technique was obtained with the help of long torments with this unit. More than 50 cars were made in this way. inside the archive is located photo boards and what needs to be done. This archive is available to all forum participants via private messages as the tests stood that.

post edited(reduced size of fonts) by super moderator !

Attached Files

ms 41 link pass!.txt
File Type:
Downloaded:	200 times
Size:	70 bytes

Please, more power for a T4 2.5 TDi year 96 102 hp, especially many lower

Thank you

Nueva carpeta.rar
File Type:
Downloaded:	52 times
Size:	66.33 KB

Hello 

Is someone able to do immo off for Peugeot 1.6 petrol mev17.4 immo off?

KTAG Read Attached

BR

Attached Files

Peugeot 207 MEV17.4-9666235880.rar
File Type:
Downloaded:	84 times
Size:	617.31 KB

could anyone check this file if it is ok.
I do not have DTC and the car do not accelerate over 3000rpm.
THANKS 

Attached Files

focus dpf 0281015242 SW1037399617.rar
File Type:
Downloaded:	62 times
Size:	890.36 KB

Hi

can you please make DPF - EGR off from the file?

Attached Files

fordoriginal.rar
File Type:
Downloaded:	69 times
Size:	390.23 KB

Hi
this utility automatically recognizes block info and otp sectors in Bosch MEDC17 files.
It is not my creation, but its creator offers freely.
Pass after thanks and rep.
Br.

   

Attached Files

MEDC17.rar
File Type:
Downloaded:	102 times
Size:	246.1 KB

hi lads is there anyone that can chksum this ecu please ?
original and tuned in attachment
my friend says with kess does chksum car starts and stops . restore original and cars ok again
thanks  

Attached Files

steve.rar
File Type:
Downloaded:	56 times
Size:	172.34 KB

Comand APS NTG2 V19 2017/2018 image disc   link on mega

 tested on dvd-r and +r datawrite and tdk ol dvd
 i used imgburn
good luck

Attached Files

Comand APS NTG2 V19 20172018.txt
File Type:
Downloaded:	99 times
Size:	117 bytes

A2118270701 2017/2018 DISC IMAGE  "not tested"
 mega link in atachment

Attached Files

COMAND APS NTG1 V18 Europe.txt
File Type:
Downloaded:	60 times
Size:	136 bytes

hi all
i need help correction km dash kongoo 2012

old km :353441 /eprom 93c66
i need 255242 km
 thanks

Attached Files

93c66 org.rar
File Type:
Downloaded:	51 times
Size:	325 bytes

I have a small prob with the car,i want the ori file so i can compare with mine.!

My read with ori ktag attached...

I could use
the update sw 9677572780 if anyone has it.!

Attached Files

hw9664738680 sw 9663193780 peugeot 208 bosch mev17.4.rar
File Type:
Downloaded:	56 times
Size:	723.84 KB

bosch mev17.rar
File Type:
Downloaded:	65 times
Size:	620.77 KB

Hello guys,
Anyone know the solution for Immo Off for BMW E46 3.0d 184hp Bosch EDC15C4?
THX!

Hello I need advice to make Swirl Flaps and EGR Off Mercedes W211 E220 CDI 
ECU DELPHI
A 646 150 99 78  HW 50.05
A 003 446 90 40  SW 27.06
CRD.11 OM646 EVO

Hi friends.

free for all, just click on usuals buttons if it helped you.

here is the original service, not a stolen job, always up to date

procedure : ASK TIGUAN MEMBER


warning : sometimes ecu pcb is the same and compatible but the box may be a little different (ex : positions of holes)

PASS ONLY IN PM, don't polute thread

Mikaela

Attached Files

link.rar
File Type:
Downloaded:	205 times
Size:	201 bytes

- SP-DATEN DATA v50.2WinKFP, Tool32, NCS Expert, BMW Coding Tools Diagnostic
- How to update NCSExpert (with progman or ISTA files)

Pass after pressing Thanks and REP!

Request password ONLY PM!

Attached Files

SP-Daten v50.2.rar.rar
File Type:
Downloaded:	119 times
Size:	36.13 KB

Hi 

I have Nissan Almera 2003 with petrol engine , need immo off . Ecu from it is Hitachi MEC32-220  C1 2829 . 
Any one have solution ?

Since i saw that here are some debates about who's tool is better, i decided to share this story with you guys.

Few days ago my Galletto broke, it can't read or write in BDM mode... As i had work to do, i rememered that Xprog have function to read EDC16 in BDM mode so i have experimented with one ecu that i had lying around my desk... First of all, it has a bit more complicated wiring diagram compared to galletto, and you need to choose what you want to read. The software automatically detects flash and eeprom type and reads it ok, but much slower than Galletto. I also tried to write data back to ECU, it was ok. Or i thought so, because i didn't test that ecu on the car...
Yesterday  I did dpf+egr off with help from a friend, and since i like to backup everything, i did BDM read using Xprog. Everything was fine until i tried to write modded file... Wiriting was ok,but when Xprog tried to verify written data, error comes out! Ok, tried to write and read again few times until i got written data identical to the source file, because Xprog reported few write errors. After comparing and no differences found, I tought that everything is ok... But it's not ok! There is one detail that i knew from before: Xprog doesn't calculate checksum,and i was prepared for that with calculated file. A friend suggested that i try to write file again with my old MPPS or VCP...
This morning as always, i tried to read data through OBD with VCP, it won't read. Tried with MPPS, still nothing. So i decided to play Russian roulette and tried to write with MPPS... It wrote it OK and car started...
The moral of the story is:
There is no perfect tool, every tool is good for something and bad for something else. Always have a plan B(or tool B).

Happy Birthday

100 years happy......Milanezu

Attached Files

Thumbnail(s)
   

Anyone needs help with cat ET install let me know, I will gladly help you just remember to rep and thanks.

If anyone is having issues installling allison 2017, just remember I am a pm away, and I can help you out no problem.
(remember to rep and thanks for the help.)

If anyone is having trouble installing DLB god mode, just send me a pm and i will be able to help you out.
(Remember to rep and Thanks if I helped you out.)

Anyone having any issues installing Jpro, I am here to help you out, just send me a PM and I will gladly help you.
(Remember to rep and thanks for the help.)

Hi
I need completly remove lambda cat in this ecu: 03C906024 IAW 4HV.
Thanks for any help.

Attached Files

polo marelli 4HV ori.zip
File Type:
Downloaded:	70 times
Size:	279.06 KB

hi all members
my skp stop working asking for add tokken
message"can be use 0 times please........add token..."
i have update it with all files existing in the net without success.
did any one fashed this device ?
br